一.干涉的定義

機器人在作業過程中，或者在運行過程中，兩個或兩個以上的機器人同時占有同一區間位置而發生沖突叫干涉。因?yàn)楦缮婵赡芤鸬暮蠊校?/p>

二.干涉區間

同一工位的機器人，在工作過程中，需要進入到同一個區域，但在進入的先后次序無嚴格的限定，一臺機器人(Master)具有絕對優先的權利，即該機器人首先進入干涉區，作業完成之后另一臺機器人(Slave)才可以進入該干涉區工作。任意一臺機器人先進入(Master)，在工藝上都允許（除了影響運行時間外），允許使用干涉區信號對控制機器人運行，防止機器人之間碰撞。對于有嚴格的工藝時序的干涉，采用互鎖信號來控制。這種干涉區信號設置方法如圖所示。 ⑴如圖中，Rob2機器人為Master,Rob1機器人為Slave. Rob1和Rob2機器人在進入干涉區之前首先分別對彼此進行初始化（開啟干涉區監控并釋放干涉區）。 ⑵機器人進入干涉區三種情形：

⑶待進入干涉區的機器人必須等待已進入干涉區的機器人完成運動退出干涉區后方可進入。

三.干涉區間互鎖編程思路：

創建名為Interlock的程序主要適用于存在有關聯的機器人組之間互鎖，該程序包含源代碼SRC文件和數據文件DAT兩個文件：

1.Interlock.dat數據文件說明：

①枚舉類型互鎖指令E_LOCKTYPE：

GLOBAL ENUM E_LOCKTYPE ENTER_LOCK_M,ENTER_LOCK_S,LEAVE_LOCK,CYC_CONTROL,RESET_LOCK

②結構體型互鎖信號S_LOCKSIG：

GLOBAL STRUC S_LOCKSIG INTROB_IN,INTROB_OUT

③用于診斷的當前機器人激活干涉區號zLockNumber：

GLOBAL INT zLockNumber=3

④干涉區監控的中斷及循環旗幟的定義：

GLOBALCONSTINTczCollInterrupt=1;定義干涉區監控的中斷等級GLOBALCONSTINTczCycCollision=1 ;定義干涉區監控的循環旗幟號

⑤信號安全檢測時間，與SPS掃描周期：

GLOBALCONSTREALcrDeadtime=0.200000003 ;信號安全檢測時間，與SPS掃描周期

⑥干涉區互鎖信號：

SIGNAL giRobotInterlock $IN[89] TO $IN[104] ;許可當前機器人進入干涉區的輸入信號組SIGNALgoRobotInterlock$OUT[89]TO$OUT[104] ;當前機器人進入干涉區請求的輸出信號組DECLS_LOCKSIGTABLE_LOCK[16];定義機器人干涉區的互鎖表TABLE_LOCK[1]={ROB_IN89,ROB_OUT89};機器人干涉區的互鎖1TABLE_LOCK[2]={ROB_IN 90,ROB_OUT 90} ;機器人干涉區的互鎖2TABLE_LOCK[3]={ROB_IN 91,ROB_OUT 91} ;機器人干涉區的互鎖3TABLE_LOCK[4]={ROB_IN 92,ROB_OUT 92} ;機器人干涉區的互鎖4TABLE_LOCK[5]={ROB_IN93,ROB_OUT93};機器人干涉區的互鎖5TABLE_LOCK[6]={ROB_IN94,ROB_OUT94};機器人干涉區的互鎖6TABLE_LOCK[7]={ROB_IN95,ROB_OUT95};機器人干涉區的互鎖7TABLE_LOCK[8]={ROB_IN 96,ROB_OUT 96} ;機器人干涉區的互鎖8TABLE_LOCK[9]={ROB_IN 97,ROB_OUT 97} ;機器人干涉區的互鎖9TABLE_LOCK[10]={ROB_IN 98,ROB_OUT 98} ;機器人干涉區的互鎖10TABLE_LOCK[11]={ROB_IN 99,ROB_OUT 99} ;機器人干涉區的互鎖11TABLE_LOCK[12]={ROB_IN 100,ROB_OUT 100} ;機器人干涉區的互鎖12TABLE_LOCK[13]={ROB_IN 101,ROB_OUT 101} ;機器人干涉區的互鎖13TABLE_LOCK[14]={ROB_IN 102,ROB_OUT 102} ;機器人干涉區的互鎖14TABLE_LOCK[15]={ROB_IN103,ROB_OUT103};機器人干涉區的互鎖15TABLE_LOCK[16]={ROB_IN 104,ROB_OUT 104} ;機器人干涉區的互鎖16

2.Interlock.src源程序文件說明：

①Interlock源程序包含以下子程序：

②互鎖程序ANTI_COLLISION(eiLockType:IN,ziLockNum:IN)：

●#ENTER_LOCK_M程序邏輯：

●#ENTER_LOCK_S程序邏輯：

●#LEAVE_LOCK程序邏輯：

●#RESET_LOCK程序邏輯：

●#CYC_CONTROL程序邏輯：

代碼：

DEF Interlock( )END;-------------Interlock Active----------------------GLOBAL DEF ANTI_COLLISION(eiLockType:IN, ziLockNum:IN)DECL E_LOCKTYPE eiLockTypeDECL INT ziLockNumDECL BOOL nbOKCONTINUEIF VARSTATE("ziLockNum")<>#INITIALIZED THEN MsgQuit("Lock area not initialized") HALT ELSE IF ziLockNum>16 OR ziLockNum<1 THEN MsgQuit("Lock area msut be 1 to 16!") HALT ENDIFENDIFSWITCH eiLockType ; --- Enter Collision Zone as Master --- CASE #ENTER_LOCK_M WAIT SEC 0 INTERRUPT DISABLE czCollInterrupt ; Disable Monitoring IF ($IN[TABLE_LOCK[ziLockNum].ROB_IN]) THEN $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=FALSE ELSE nbOK=FALSE MSG_ANTICOLL(ziLockNum) REPEAT IF ($IN[TABLE_LOCK[ziLockNum].ROB_IN]) THEN nbOK=TRUE ELSE nbOK=FALSE ENDIF WAIT SEC 0.01 ; Sampling 100 ms UNTIL (INSTRUCTION_OK==TRUE) $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=FALSE ENDIF INTERRUPT ENABLE czCollInterrupt ; Enable Monitoring ; --- Enter Collsion Zone as Slave --- CASE #ENTER_LOCK_S WAIT SEC 0 INTERRUPT DISABLE czCollInterrupt ; Disable Monitoring nbOK=FALSE MSG_ANTICOLL(ziLockNum) REPEAT IF ($IN[TABLE_LOCK[ziLockNum].ROB_IN]) THEN $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=FALSE WAIT SEC crDeadtime IF ($IN[TABLE_LOCK[ziLockNum].ROB_IN]) THEN nbOK=TRUE ELSE nbOK=FALSE $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=TRUE ENDIF ENDIF WAIT SEC 0.01 ; Sampling 100 ms UNTIL (nbOK==TRUE) $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=FALSE INTERRUPT ENABLE czCollInterrupt ; Enable Monitoring ; --- Leave Collision Zone --- CASE #LEAVE_LOCK CONTINUE IF NOT $ON_PATH THEN WAIT FOR $ON_PATH ENDIF TRIGGER WHEN DISTANCE=1 DELAY=0 DO $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=TRUE; --- Initialize Collision Zone --- CASE #RESET_LOCK WAIT SEC 0 WAIT FOR $ON_PATH $OUT[TABLE_LOCK[ziLockNum].ROB_OUT]=TRUE ; --- Prepare for permanent Monitoring--- CASE #CYC_CONTROL GLOBAL INTERRUPT DECL czCollInterrupt WHEN NOT $CYCFLAG[czCycCollision] DO STOP_ROB( ) INTERRUPT OFF czCollInterrupt $CYCFLAG[czCycCollision]=TRUE $CYCFLAG[czCycCollision]=(((goRobotInterlock B_EXOR 'B1111111111111111') B_AND giRobotInterlock) == (goRobotInterlock B_EXOR 'B1111111111111111')) INTERRUPT ON czCollInterrupt INTERRUPT ENABLE czCollInterrupt; --- WARNING: Program Failure Interlocks --- DEFAULT HALT MsgNotify("Unknown Collision Setting!Please Switch Ti Mode!") WAIT FOR $T1ENDSWITCHENDGLOBAL DEF STOP_ROB ( ); *** Stop Movement by Interlock Monitoring*** BRAKE setmsg (99,3,0) WAIT FOR $CYCFLAG[czCycCollision]ENDGLOBAL DEF Msg_Anticoll(ziLockNum :IN)DECL INT ziLockNumDECL REAL nrTimernrTimer=0.0zLockNumber=ziLockNum;Message Outputsetmsg (ziLockNum,1,nzTimer) $TIMER_STOP[20]=TRUE$TIMER[20]=0$TIMER_STOP[20]=FALSEREPEAT WAIT sec .01UNTIL ($IN[TABLE_LOCK[ziLockNum].ROB_IN])==TRUE$TIMER_STOP[20]=TRUEnrTimer=$TIMER[20]nrTimer=nrTimer/1000.0setmsg (ziLockNum,2,nrTimer) ENDGLOBAL DEF SetMsg(ziLockNum:IN,ziMsg:IN,riPar:IN )DECL KrlMsg_T MsgDECL KrlMsgPar_T Par[3]DECL KrlMsgOpt_T OptDECL INT nzHandleDECL INT ziLockNum, ziMsgDECL REAL riPar;Select Msssage Text---------------------SWITCH ziMsg CASE 1 ;Interlock is Active Msg = {Modul[] "Interlock", Nr 007, Msg_txt[] "Interlock Area %1 is Active!"} CASE 2 ;Interlock was active Msg = {Modul[] "Interlock", Nr 008, Msg_txt[] "Interlock Area %1 was active %2[s] ago!"} CASE 3 ;Interlock Cycflag has triggered Msg = {Modul[] "Interlock", Nr 009, Msg_txt[] "Collision Monitoring has Triggered!"}ENDSWITCH;Configuration of message parameter --------Par[1] = {PAR_TYPE #VALUE, PAR_INT 0}Par[1].PAR_INT = ziLockAreaPar[2] = {PAR_TYPE #VALUE, PAR_REAL 00.0}Par[2].PAR_REAL = riPar;Message Options ------------------------------------Opt = {Vl_STOP FALSE, CLEAR_P_RESET TRUE, CLEAR_P_SAW FALSE, LOG_TO_DB TRUE};Message generation---------------------------nzHandle = SET_KRLMSG (#NOTIFY, Msg, Par[], Opt)END

四.互鎖信號程序的使用：

1.初始化干涉監控：

ANTI_COLLISION(#CYC_CONTROL,0 )

2.重置并釋放干涉區信號-依據自己需求：

ANTI_COLLISION(#RESET_LOCK,1)ANTI_COLLISION(#RESET_LOCK,2)ANTI_COLLISION(#RESET_LOCK,3)ANTI_COLLISION(#RESET_LOCK,4)ANTI_COLLISION(#RESET_LOCK,5)ANTI_COLLISION(#RESET_LOCK,6)ANTI_COLLISION(#RESET_LOCK,7)ANTI_COLLISION(#RESET_LOCK,8)

3.進入干涉區：

-作為主機器人進入：

ANTI_COLLISION(#ENTER_LOCK_M,3)ANTI_COLLISION(#ENTER_LOCK_M,4) ；三臺機器人同時進入該區域ANTI_COLLISION(#ENTER_LOCK_M,5)

-作為從機器人進入：

ANTI_COLLISION(#ENTER_LOCK_S,3)ANTI_COLLISION(#ENTER_LOCK_S,4) ；三臺機器人同時進入該區域ANTI_COLLISION(#ENTER_LOCK_S,5)

復雜的互鎖建議最好由PLC來統一處理；

4.退出干涉區：

ANTI_COLLISION(#LEAVE_LOCK,3)

五.說明：

本文主要講述絕對優先干涉區的設定，此種方法必須區分主次關系，主機器人獲得絕對的優先處理的權力，而從機器人在遇到主從機器人同時進入干涉區時，獲得的優先級低于主機器人，必須等待主機器人處理完退出干涉區之后才能進入。